|
|
|
 
Hoffmann MS35SF
Double Miter Saw with infeed and outfeed tables,
support stands and digital length stop
Call for price quote.
|
The Hoffmann MS 35 SF Double Miter Saw is equipped with
two sawing and routing stations, mounted at a fixed 90
degree angle to each other. Each station consists of a
sawblade to cut the material, and a routing head to rout
either one or two dovetail keyways per miter.
Solid hard and softwood as well as panel products like MDF,
MDO, particleboard or plywood can be cut to size and
routed for Hoffmann dovetail keys in one cycle.
|
|
The
maximum material width is 3 1/2" = 89mm, the maximum
material thickness is 4" = 100mm.
The routing height for each keyway position can be
adjusted by the operator from 0 - 3" = 0-76mm.
Different routing heights can be set for each position to
allow the processing of profiled moulding or material joined
with a compound miter.
The
key locations can be adjusted by the operator from 1/4"
- 3 1/8" = 6-80mm, measured from the tip of the mitered
end. These adjustments are displayed on calibrated "SIKO"
counters, assuring perfect repeatability.
The
material is placed onto the material support on the left
side of the machine. The operator actuates
the pneumatic foot switch to secure the workpiece
with eight pneumatic clamps. These clamps are
mounted
behind the sawblade guard for added safety.
Once
the material is secured, the operator must press two buttons
at the front of the machine simultaneously to initiate the
cutting and routing cycle. This two-hand-control design
forces the user to have both hands out of harms way.
PHOTOS
TO THE RIGHT SHOW SAFETY GUARDS REMOVED FOR ILLUSTRATION
PURPOSES
|
DETAIL
|
-
Sawblades
cut through material and retract up to their home position.
-
Both
halves of the machine table move approx. 18" apart
to create a space for the routing heads.
-
Routing
heads move up to rout the first key location, then down,
over and up again to rout the second location.
-
The
tables move back to the center of the machine and the
pneumatic clamps release the material.
The
MS 35 SF is equipped with a 7 3/4" wide aluminum
fence on the right side of the machine. This fence is
63" = 160cm long, longer lengths are available. The
width of 7 3/4" assures sufficient support, even
for wider material. Moving the stop assembly to the desired
location and locking it in place sets the workpiece length.
The length measurement is shown directly on the stop assembly
with a digital display, the accuracy is .001" = .01mm.
The operator can change the display from fractional inches
to decimal inches or decimal millimeters.
An infeed material support table is supplied for the left
side of the machine,
the length is 63" = 160cm.
The
Hoffmann MS 35 SF is shipped ready for operation, including
infeed support table, right hand side fence system with
digital display, solid carbide router bits installed,
air filter-regulator-lubricator assembly installed, two-hand
safety operation, separate flow control valves for sawblade
and routerhead feed rate, emergency-stop-switch, manual
and toolkit.
|
>>Technical
Specifications:
| Power:
|
220 Volts,
3 Phase, 60 Cycles, 15 Amperes |
| Air
Supply: |
90 psi |
| Router
heads: |
two motors
@ 450 Watt, 24,000 rpm, 6.00mm collet |
| Saw
heads: |
two
motors @ 2 1/2 HP, 3,470 rpm |
| Sawblades:
|
350mm
diameter, 30mm bore, carbide tipped |
| Router
bits: |
Hoffmann
solid carbide router bits, W-1, W-2, W-3 |
| Cutting
capacity: |
3 1/2"
max. width, 4" max. thickness |
| Sawblade
cutting angle: |
45 degrees |
| Min.
material length: |
3" |
| Max.
material length: |
96",
longer lengths possible with extended fence and table |
| Operation:
|
two-hand
safety controls |
| Controls:
|
electronic
- pneumatic operation with PLC |
| Dust
collection: |
two dust
collection ports, 4" diameter, 400cfm each |
| Overall
dimensions: |
57"
length
66"
height
40"
depth
220"
total length w table extensions
Weight
approx. 1665 lb.
|
|
|
|
